A HackRF-portapak-inspired firmware for the Baofeng DM-32UV, built on the RadioFoundry tree. The radio boots into a two-by-three app grid, and each app is a small transmitter with its own panel. Transmission is app-driven: there is no manual PTT in this build.
Web flasher: dm32mayhem.com — back up, install and restore the firmware over the programming cable in Chrome or Edge.
Home (RX, TX, TRX, About, Config, Diagnostics) and the TX app grid. RX has the RTTY receiver; TRX holds the FM transceiver app.
Every power-on opens with the responsibility notice and a six-digit code generated for that boot. No app, key or transmitter is available until the code is typed; Back deletes a digit, and a wrong code clears the entry and asks again. It is an acknowledgement, not a security lock: the code is on the panel.
| App | What it sends |
|---|---|
| SAME TX | NOAA/EAS SAME headers over FM AFSK |
| OOK TX | On-off keyed PA: a hex code or a de Bruijn sequence |
| MDC-1200 TX | Motorola MDC-1200 ANI/PTT ID and the other opcodes |
| P25 CC TX | A P25 Phase 1 control channel |
| APRS TX | APRS status, message and position packets |
| RTTY TX | ITA2/Baudot RTTY |
The RX grid has the RTTY receiver; the TRX grid has the FM transceiver (a tuned VFO with live PTT, offset and CTCSS RX/TX).
The standard SAME header (ZCZC-ORG-EEE-PSSCCC+TTTT-JJJHHMM-LLLLLLLL-, three repeats, 520.83 baud AFSK) built from an
originator, event, FIPS state and county, valid time, station ID and frequency. The issue time comes from the radio's
GPS when it has one, otherwise the standard placeholder.
On-off keying by switching the PA drive at the bit rate. A hex code or the binary de Bruijn sequence, encoded as the
common PWM remotes expect (0 = 1000, 1 = 1110), with frequency, bit length, repeats and de Bruijn order. One
millisecond is the default bit length: shorter pulses do not let the PA bias settle.
PTT ID/ANI, emergency, radio check, stun and unstun, call alert, sel call 1/2, status request/response, remote monitor and message. The PDU carries the CRC, convolutional code and interleave, NRZI-encoded, as 1200 baud AFSK (mark 1800 Hz, space 1200 Hz).
A P25 Phase 1 control channel: frame sync, BCH NID, and rotating IDEN_UP, NET_STS, RFSS_STS and group voice grant TSBKs. The site is set by NAC, WACN, system ID, RFSS, site, talkgroup and voice channel; the bytes go through the modem's physical-layer 4FSK transmitter.
Compose and send an APRS status, a text message to a callsign, or the current position. The APRS engine frames the AX.25, keys, retries and tunes; the app shows the radio's APRS callsign, frequency and why a send is blocked.
ITA2/Baudot RTTY at 45.45 or 50 baud, with selectable mark and shift (space = mark + shift), a repeated message and a long text field, sent through the AFSK path.
- AFSK (SAME, MDC-1200, RTTY) through the HR_C7000 FM modulator at 8 kHz PCM.
- OOK by switching the PA drive (DAC B) at the bit rate.
- P25 through the HR_C7000 physical-layer 4FSK transmitter in 36-byte blocks.
- APRS through the existing APRS engine.
The radio task owns the transmitter: each app queues a job and the APRS/transmit service keys, tunes and unkeys. The
long text editor on the apps holds 128 characters and shows the tail while typing. The boot gate (CONFIG_BOOT_GATE)
runs in the UI task before it enters the app grid: it generates the code, consumes every key until the code matches,
and keeps auto power off from firing while it waits.
Open dm32mayhem.com/flasher in Chrome or Edge on a desktop computer, or Chrome on Android, and connect the radio's programming cable. Install backs up the radio first, then writes the codec-less DM32Mayhem image, merging the radio's own DMR voice codec. Update writes the latest image over a radio already running DM32Mayhem. Back Up and Restore use the same backup bundle; Radio Stuck in Update Mode recovers a radio left in its loader.
The lean DM32 app firmware is built by tools/build-bbs.sh (the historical name; it now builds the app grid):
tools/build-bbs.sh # -> firmware/build/bbs/rfoundry_dm32.bin
The image has no DMR voice codec slot (codecs/ is empty here); FM and packet are unaffected. Flash with the runtime
stub (radio on):
cd firmware
python3 stub/stubtool.py /dev/ttyUSB0 --board dm32 --rfoundry-enter \
--write-app build/bbs/rfoundry_dm32.bin
python3 stub/stubtool.py /dev/ttyUSB0 --attach --boot reset
The full RadioFoundry build (make BOARD=dm32) is untouched and still builds.
| Path | What |
|---|---|
firmware/ |
the vendored RadioFoundry tree |
firmware/core/bbs/ |
the original packet BBS (kept, no longer the UI) |
firmware/core/same/ |
SAME header encoder |
firmware/core/ook/ |
OOK bit patterns and the de Bruijn sequence |
firmware/core/mdc/ |
MDC-1200 encoder |
firmware/core/p25cc/ |
P25 control channel frames |
firmware/core/rtty/ |
ITA2/Baudot encoder |
firmware/core/ui/ui_menus.c |
the app grid and the app screens |
docs/screenshots/ |
the screenshots in this README |
terminal/ |
KISS-over-TCP AX.25 client (needs a build with the network services) |
tools/build-bbs.sh |
the app firmware build |
- FM and packet only in this build: no AMBE codec, so no DMR voice.
- No manual PTT; apps key the radio themselves.
- The boot gate is an acknowledgement, not encryption or access control: the code is shown on the panel.
- OOK is limited by the PA settling time, about 1 ms per bit.
- RX has the RTTY receiver; TRX has the FM transceiver.










